Hauppauge Wintv Hvr 950 Mac Drivers

  1. Wintv Hvr 950 Windows 10
  2. Hauppauge Wintv-hvr 950
  3. Hauppauge Wintv Hvr 950 Mac Drivers Windows 7
  4. Hauppauge Wintv Hvr 950 Mac Drivers Manual

To the Plex team, I know that you will support more devices, and I hope that the Hauppauge WinTV-HVR-950Q will be in the next release of the supported devices so I will renew my plex pass subscription! Thank you all. And I’m open to any work-arounds until then! Leave your WinTV-HVR-930C plugged into your PC. Follow the following steps: Download the WinTV-HVR-930C driver update. Click to install. This will install the WinTV-HVR-930C Windows driver. At the completion of the driver install, you should see a message which says Drivers have been updated successfully. Latest applications and driver updates. Note: If you have run HCWCLEAR, you must reboot your PC and leave the WinTV-HVR-850 installed.After a reboot you will see the Found New Hardware Wizard installation message, hit Cancel. Then continue below. Note: to use the WinTV-HVR-850 with the Windows Media Center application, click the Windows Media Center install tab above.

The WinTV 10, WinTV v8.5 and WinTV v8 applications includes the latest Windows driver

Note: to use the WinTV-HVR-955Q with Windows Media Center, click the Windows Media Center install tab above.

New product installs:

If you have recently purchased a new WinTV product and your WinTV v8.5 Activation Code has never been used, you can install WinTV v10 with this code. This only applies to unused WinTV v8.5 Activation Codes.

Installation notes for WinTV v8.5:

If you have one of the following products: a Hauppauge WinTV-HVR-850, WinTV-HVR-950, the original Colossus or HD PVR model 1212, you must use WinTV v8 or WinTV v10. WinTV v8.5 does not support these products.

A WinTV v8.5 Activation Code will be needed to install this WinTV v8.5 version. If you do not have an Activation Code, but you have a WinTV v7 CD, you can install the WinTV v8 application.

If you do not have an Activation Code: If you do not have a WinTV v8/8.5 Activation Code, you can purchase the new WinTV v10 Activation Code on the Hauppauge webstore for $12.95. This can be used with WinTV-HVR, WinTV-dual and WinTV-quad products, as well as the HD PVR series of HD recorders plus USB-Live2 and the ImpactVCBe.

Extend: If you have an Activation Code for WinTV v8 or v8.5 with Extend, the latest version of WinTV v8.5 with Extend will automatically be installed.

Installation on multiple computers: the WinTV application can be installed on as many PCs as needed as long as you use the same Hauppauge device. We link the serial number of your TV tuner (sometimes it's the MAC address) with the Activation code. So as long as you use the same Hauppauge device, you can install on more than one computer.

WinTV v8.5 application and Windows driver package

This download is a complete WinTV v8.5 application, including Windows drivers for supported WinTV products plus utilities.

WinTV v8.5 Installer
For Windows 10, 8, and 7

Version: 37350 File size: 101 MB Date: Dec. 24, 2019
Release notes Backup download site Previous version

To install the WinTV v8.5 application

  • Step 1: Download the WinTV v8.5 installer by clicking the download button above. The WinTV v8.5 Installer is normally saved in the Download folder on your PC
  • Step 2: Run wintv85setup from the Download folder on your PC. Halfway through the installation, a message will pop up asking for you to enter the Activation Code.
  • Step 3: At the Activation required screen, click on Enter Activation code and enter the activation code which was emailed to you, is printed on the WinTV v8 activation card or printed on your WinTV v8 CD. You do not need to enter the dashes, and you can use upper or lower case characters.
  • Step 4: When the installation is complete, you will find the WinTV icon on your Windows desktop. Double click on this icon and the WinTV application will run. On the first run of WinTV, it will automatically go through the TV source selection and will scan for channels.

To install the latest driver:

Leave your WinTV-HVR plugged into your PC. Follow the following steps:

  • Download the WinTV-HVR driver update
  • Run HCWDRIVERINSTALL.EXE.
  • This will install the WinTV-HVR base driver. At the completion of the driver install you should see a message which says Drivers have been updated successfully.

SoftMCE Setup

File name: SoftMCE_setup.exe
File size: 2.3 Mb
Date: 4/14/2010

Setting up your TV tuner in Windows 7 Media Center

Bug fixes for the Windows Media Center 'Low bit rate' error message

Microsoft has released Windows Media Center patches for the 'Low bit rate' error message.
Click to view the information from Microsoft.

Remapping clear QAM channels in Windows 7 Media Center

WinTV Digital Signal Strength Indicator

The WinTV Digital Signal Strength indicator displays information about the quality of the digital TV channel you are watching. This application is used with the WinTV v10, 8 and v7 applications.

The WinTV Digital Signal Strength must be used with one of the Hauppauge WinTV applications. It cannot be used stand alone.

Click here for instructions on using this application.

IR Remote control application

Remote control applet. After you run this applet, an icon will appear in your Windows device tray showing that the Hauppauge remote control is active.

Name: 2.71.33113_IR32.exe
Size: 450KB
Updated: April /2015

WinTV-Scheduler update for WinTV version 6

This TV program scheduler for WinTV version 6 allows 'background recording' on dual tuner WinTV products.

Name: sched25_26071.exe
Size: 3.8 MB
Updated: March 11, 2008

NextPVR

NextPVR is a free Personal Video Recorder (PVR) and Media Centre application for Microsoft Windows. NextPVR works with most Hauppauge TV tuners.

JRiver Media Center

JRiver Media Center is a TV application for managing and playing digital media. JRiver Media Center can record and play Over-The-Air and Cable TV broadcast channels using TV tuners from Hauppauge. You can currently record on one machine and watch on another, or on a tablet. All the user has to do in install the drivers for their Hauppauge product and JRiver Media Center can do the rest. You can download a fully featured version of the product on a 30 day trial from www.JRiver.com to experience the magic of JRiver Media Center.

Please see our Linux page for Ubuntu and Plex instructions:please see here.

For the Hauppauge close source Linux driver, please send an e-mail message to: jfox@hauppauge.com

Linux for the WinTV-HVR-950Q

WinTV version 6 users manual

WinTV version 6 users manual
Updated: October 15, 2007

Making a TV connection to your WinTV

WinTV v10 Introduction
click to play video
Scheduled recording with the built-in EPG
in WinTV v10
click to play video
Wipe out your channel database and
rescan for channels
click to play video
WinTV v10 scheduling recordings with TitanTV
click to play video
How to setup an analog video source
Click to play video
How to setup an analog video source (channel 3)
Click to play video
How to scan for FM radio stations in WinTV
click to play video
How to change the battery in a
Hauppauge -005 remote control
click to play video
Hvr

What Operating Systems are supported by the WinTV-HVR-955Q?

  • Microsoft® Windows® 10, 8 and 7, Windows Vista, either 32-bit or 64-bit versions
  • Windows XP, Windows XP Pro or Windows XP Media Center Edition, with Service Pack 2 ( or greater.)

Can I use the WinTV-HVR-955Q with Media Center?

Yes, the WinTV-HVR-955Q can be used with Windows Media Center in Windows 8, 7, Vista and with Windows XP Media Center Edition 2005.

To use the WinTV-HVR-955Q with Windows Media Center, download and install the Windows Media Center driver installation package, which will install the WinTV-HVR-955Q Windows driver and the Hauppauge MCE Soft Encoder.

Note: Under Windows 7, the Hauppauge MCE Soft Encoder is pre-installed as part of Windows 7. Therefore, you can skip the installation of the MCE Soft Encoder and simply install the WinTV-HVR-950Q Windows driver.

Note: under Windows Media Center, you will only be able to configure WinTV-HVR-955Q as either an Digital tuner or an Analog tuner. You will not be able to switch between Digital and Analog channels.

What type of channels will I receive with the WinTV-HVR-955Q?

NTSC Analog CableTV or over-the-air analog TV: You can use your cable TV from the wall to connect to the WinTV-HVR-950Q and receive all of your basic Cable TV channels. You can also use a roof top antenna to receive 'over-the-air' TV.

Note: After June 2009, most areas in the United States no longer broadcast over-the-air analog signals.

ATSC over-the-air digital TV: Supports all ATSC formats, up to the high definition 1080i format!
Note: For ATSC digital TV, a rooftop/out door antenna is recommended for optimal results/signal strength.

ClearQAM cable TV Channels: Clear QAM digital cable TV channels are unencrypted digital cable TV channels. Clear QAM allows users to watch unencrypted digital TV channels from their cable TV provider without a set-top box.
Note: WinTV v8, v8.5, WinTV v10 or Microsoft Windows 7 is required for clear QAM reception
Note: Check your local cable TV provider for clear QAM reception over your cable TV network.

Can I get HD with the WinTV-HVR-955Q through my Cable or Satellite box?

No. The WinTV-HVR-955Q has an ATSC over-the-air digital TV tuner built-in and supports all ATSC formats, up to the high definition 1080i format . The WinTV-HVR-950Q will support ATSC broadcasts that are currently being transmitted over-the-air. It will not be able to decode HD broadcasts that come through your cable or satellite box. The WinTV-HVR-955Q also supports clear QAM cable TV channels through your direct cable TV line if available from your cable TV provider.

What type of recordings can I make with the WinTV-HVR-955Q?

Using the WinTV v8, v8.5, WinTV v10 application, the WinTV-HVR-955Q will record in a transport stream (TS)
For ATSC and Clear QAM digital TV recordings, the recording format and bit rate is exactly the same as the broadcast format (i.e. ATSC 1080i is recorded at 1080i).
For NTSC analog cable TV recordings, our SoftPVR is used to create Transport Stream files (TS)

Note: TS files can be converted to MPEG files using options in the WinTV 7 configuration menu.

Note: The WinTV 6 application recording are in MPEG format for both digital and analog.

Note: Not all recordings made with ATSC/QAM signals are DVD compliant.

Can I record one show while watching another with the WinTV-HVR-955Q?

No. The WinTV-HVR-955Q will only be able to record the program that is being viewed using the WinTV v8, v8.5, WinTV v10 application. But the Hauppauge WinTV v8/8.5/10 application allows up to 4 WinTV-HVR-955Q's to be used in one system at a time.

Black video window or choppy video when watching a digital TV channel

If you are watching a digital TV channel and you see choppy video, no audio or a black screen, then it is possible your PC is not fast enough to decode and play the digital TV channel you are watching. Please verify that your system meets the minimum requirements for using the HVR-950Q

Digital TV, especially ATSC high definition digital TV, is very CPU intensive. Many graphics cards have special built-in hardware to speed up decoding of high definition TV channels.

On graphics cards without special video decoding features, you can often improve the playback performance by using the Video Renderer settings located in the settings menu of WinTV 7. To open the setting menu click on the “gear” button located in the lower left of the WinTV 7 screen.

The default mode is EVR. The other modes are VMR9, VMR7 and Overlay. Each mode uses a different process to render video. Try each mode and use the one which gives you the best results. To use hardware acceleration put a check in the box “use hardware acceleration when possible. This will allow your graphics system to use hardware acceleration for video decode. Note: graphics hardware acceleration does not work on all systems. After making a change in video rendering settings Wintv must be restarted to take effect.

If you are using WinTV 6 then the render options are part of a separate program called Primary. Changes in the Primary applet must be made with the WinTV application closed. Open the Primary program by going to Start – All Programs – Hauppauge WinTV – Primary. After making changes close the Primary applet and open the WinTV application.

How do I enable my remote control so it will work with the WinTV-HVR-950Q?

The IR software should be installed by default. To check look for a small remote control icon in the Windows task bar on the lower right. IF it is not present you can reinstall Wintv from the installation CDROM or download IR32.EXE from our support web site. The remote control must also have “line of sight” with the HVR-950Q. The IR receiver of the HVR-950Q is the round bulb on the side of the unit.

I receive a 'Low bit rate' error message when using Windows Media Center in Windows 7.

Microsoft has released Windows Media Center patches for the 'Low bit rate' error message.
Click to view the information from Microsoft.

WinTV application locks or stops responding during analog scan under Windows 7.

In order to fix this issue, please check that your Power Options setting is not set to ‘Power Saver’. Please change it to ‘Balance’ or ‘High Performance’.

To change these settings on Windows 7, please do the following.

Click on Start and then Control Panel.

If Control Panel is set to View by: Category then click on ‘System and Security’ and then ‘Power Options’.

If Control Panel is set to View by: Large or Small icons then click on ‘Power Options’.

If you do not see Balanced or High Performance please click on the option for ‘Show additional plans’.

Once you make the change please restart your system. When the system restarts please rescan again for channels.

What file size will the recorded videos be?

Digital Broadcasts (ATSC or QAM)

The file size of a digital signal capture depends on the bitrate of the digital signal. The bitrate is set by the broadcaster and cannot be user configured. Bitrates for digital signals can range anywhere from about 1.2 Mbits/sec up to 19.3 Mbits/sec. Most of the time these bitrates are variable and not constant. Capture sizes for ATSC & QAM recordings are approximately 1.7 Gigabytes per hour up to 8.3 Gigabytes per hour.

Wintv Hvr 950 Windows 10

Analog Broadcast.

The WinTV application has to convert analog signals to digital in order to record. There are four recording profiles. The following list shows recording file sizes for burning to 4.3Gb DVD:

Best - Approx 1 Hour+
Better - Approx 1 1/2 Hours
Good - Approx 2 Hours
Fair - Approx 3 Hours

WinTV v7 does not open or opens and then disappears?

This can be caused by a corrupt Channel database so you will need to uninstall and reinstall. First you need to go to start, all programs, Hauppauge Wintv and in that folder run
“uninstall Wintv7” (or remove Wintv7 using control panel 'add/remove programs) then you need to remove the backup channel database.

Windows Vista, 7 and 8 go to C:program data ( this folder is a hidden folder so if you do not see it you need to “show hidden folders “ in your search
Options) once you can get to this folder you will see a folder label “Hauppauge” delete this folder.

Windows XP go to C:documents and settingsall usersshared documentsapplication data ( this folder is a hidden folder so if you do not see it you need to “show hidden folders “ in your search Options) once you can get to this folder you will see a folder label “Hauppauge” delete this folder.

Then download the latest version of Wintv7 located in the support section of the website and reinstall (note: you must have your original CD to validate the download.)

Windows cannot verify the digital signature for the drivers required for this device error code 52?

This appears to be a bug in windows 64 bit OS. Our drivers are signed.

'Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)'

The following is probably the easiest fix to Error Code 52 on Windows 7 or Windows 8 64bit.

In device manager right click the Hauppauge product under Sound Video and Game Controllers with the exclamation mark and select Uninstall. If you have a USB product you might multiple listings, please right click the first one on the list.

For this example we will use the HVR-950Q.

On the Confirm window please check the box for 'Delete the driver software for this device' and click OK.

Repeat the uninstall for the other two 950Q entries. (note you won't be asked to 'confirm device uninstall' again).

Once the drivers are gone on right click on 'Sound, Video Game Controllers' and 'Scan for Hardware Changes'.

Windows should now look online automatically for the 950Q drivers.

Take a look after a few minutes if the drivers are installed automatically properly under Sound Video and Game Controllers.

If they still come back as 'unsigned' try the procedure again.

Here is a chart which shows some of the things you need to know about each type of connection.

Here are some common models (please order by model number or product code):

Connecting to an over-the-air antenna

Cable or satellite TV set top box
RF output

click to enlarge

Cable or satellite TV set top box
A/V output

Connecting to a cable TV wire from the wall (Digital QAM)

click to enlarge
Which type of TV can this connection be used with?Over-the-air TVCable or satellite TV boxCable or satellite TV boxCable TV
What types of video do I select when scanning for channels in the WinTV application (Device Setup Wizard)?Digital ATSCAnalog TV (cable/antenna)External inputs (S-Video or Composite video)Digital QAM or
Analog TV (if available in your WinTV tuner)
What remote control do I use to change channels?WinTV remote controlRemote control from your set top boxRemote control from your
set top box
WinTV remote control
NotesYou can use a roof top antenna for best reception.

Most set top boxes allow you to switch to Channel 3 or 4. When you scan with WinTV, it will pick up the TV signal on the correct channel.

Some satellite receivers use channels 60, 70 or 73. But when you scan for Analog TV channels, WinTV will pick up whatever channel is being used by your set top box.

Most set top boxes have A/V connections on the back, which can go into the WinTV's A/V input.

Some cable TV networks transmit analog TV channels, so we recommend scanning for both Clear QAM and analog TV.

Not all cable TV networks transmit clear QAM. Check with your local cable TV operator for the availability of clear QAM in your area.

First time installation of WinTV v7 or during a reinstallation: “WinTV board not found” or “No TV tuner available”

Broadway while recording

Step 1: Check the status of your Hauppauge TV tuner drivers in Windows Device Manager

  • Click Windows Start, click on Control Panel and click on Device Manager
  • In Device Manager, click on Sound, video game Controllers
  • You should see your Hauppauge product

Step 2: If the Hauppauge device has a yellow exclamation mark

Click on the Hauppauge device to open it. If you see the following: 'Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)'
This appears to be a bug in Windows 64 bit OS since the Hauppauge Windows drivers are signed.

The following is the easiest fix to Error Code 52 on Windows 7 or Windows 8 64bit.

  • In Device Manager, right click the Hauppauge product under Sound Video and Game Controllers with the exclamation mark and select Uninstall. If you have a USB product you might see multiple listings, please right click the first one on the list. (For this example we will use the WinTV-HVR-950Q. )
  • On the Confirm window please check the box for “Delete the driver software for this device” and click OK
  • Repeat the uninstall for the other two WinTV-HVR-950Q entries (Note: you won’t be asked to ‘confirm device uninstall’ again)
  • Once the drivers are removed, right click on Sound, Video, Game controllers and click Scan for Hardware Changes
  • Windows should now look online automatically for the 950Q drivers
  • Take a look after a few minutes if the drivers are installed automatically properly under Sound Video and Game Controllers.
  • If they still come back as “unsigned” try the procedure again

Errors when running WinTV 7: “TVserver cannot Start” or “.NET framework' errors

This can be caused by a corrupt WinTV v7 Channel Database. You will need to uninstall and reinstall the WinTV v7 application and the Channel database to fix this.

To uninstall WinTV v7, click Windows Start, click on All Programs, click on Hauppauge WinTV run Uninstall Wintv7. You can also or remove Wintv7 using control panel 'add/remove programs'.

Then you need to remove the backup Channel database:

  • Windows Vista, 7 and 8: Go to C:program data ( this folder is a hidden folder so if you do not see it you need to “show hidden folders “ in your search Options) once you can get to this folder you will see a folder label “Hauppauge”. Delete this folder.
  • Windows XP: Go to C:documents and settingsall usersshared documentsapplication data ( this folder is a hidden folder so if you do not see it you need to “show hidden folders “ in your search Options) once you can get to this folder you will see a folder label “Hauppauge” delete this folder. Then download the latest version of Wintv7 located in the support section of the website and reinstall (note: you must have your original CD to validate the download.)

Settings.xml file is corrupt or missing

Hauppauge

Solution: Uninstall WinTV v7 and then reinstall WinTV 7

  • Click Windows Start ->Control Panel and then click Programs and Features
  • Find Hauppauge WinTV 7 and double click on this. This will start the uninstall process
  • When you are finished uninstalling WinTV v7, reinstall it from your WinTV v7 CD

Prodinfo: get information on your Hauppauge TV tuner

Prodinfo.exe is a program you can run which will extract information about the WinTV product you have installed such as model and serial number, MAC address, revision, and features which can be used to identify the exact model of your product. The driver for the device must be installed in order to run Prodinfo.exe

HCWClear: remove the Hauppauge driver and applications from your PC

HCWCLEAR.exe is a program you run to remove all driver and files that were installed with the installation of the WinTV program.

Are you getting error messages 'Setup could not detect your product', TV Tuner not available' or 'Unable to locate capture filter' after Windows 10 installed an update?

This is a known 'feature' of the new release of Windows 10, related to video cameras but also affecting TV tuners and video recorders.

The latest versions of WinTV v10, v8.5, WinTV v8 and Hauppauge Capture automatically update the Windows 10 drivers to fix this error message. If you need to manually fix this, click here.

Questions or problems? Please contact Hauppauge support at: support@hauppauge.com

  • Prodinfo: get information on your Hauppauge TV tuner

    Prodinfo.exe is a program you can run which will extract information about the WinTV product you have installed such as model and serial number, MAC address, revision, and features which can be used to identify the exact model of your product. The driver for the device must be installed in order to run Prodinfo.exe

  • HCWClear: remove the Hauppauge driver and applications from your PC

    HCWCLEAR.exe is a program you run to remove all driver and files that were installed with the installation of the WinTV program.

How to find the product code of your Hauppauge product:

Hauppauge product codes on WinTV boards are normally found on the TV tuner. This is a five digit number normally followed by a revision (REV). You need to look at the first two numbers to determine the product type. The other numbers are related to the accessories which are on the product.

On the MediaMVP, WinTV-USB and other 'boxes', the product code is normally on a label on the bottom of the case.

204109 WinTV-dualHD

203029 WinTV-soloHD

203xxx Xbox One Digital Tuner

203xxx PCTV Triple Stick 292e

166XXX WinTV-quadHD

160XXX WinTV-HVR-1975

161xxx WinTV-HVR-1265

15XXX WinTV-HVR-5525

159xxx WinTV-MiniStick2

73XXX WinTV-HVR-1900

151XXX WinTV-HVR-2215_2205

89XXX WinTV-HVR-2200_2210

650XXX WinTV-HVR-900_930

1111XX WinTV-Analog Stick

94XXX WinTV-HVR-1100

67XXX WinTV-HVR-1110

22XXX WinTV-HVR-1200

26XXX, 25XXX WinTV-PVR-150

Hauppauge Wintv-hvr 950

23XXX, 23XXX WinTV-PVR-500

164XXX HD PVR60

157XXX HD PVR Gaming Edition Plus

157XXX HD PVR2

157XXX HD PVR Gaming

158xxx HD PVR Rocket

Hauppauge Wintv Hvr 950 Mac Drivers Windows 7

131xxx Colossus

152XXX Colossus2

711XX Impact VCB-PCI-E

122XXX USB-Live2

64XXX Impact VCB-PCI

110XXX MediaMVP-HD

49XXX HD PVR

38XXX WinTV-PCI

44XXX WinTV-Go

64XXX WinTV-PCI-FM

34XXX 88X based WinTV boards

86XXX MediaMVP

48XXX WinTV-PVR-250-350

Hauppauge Wintv Hvr 950 Mac Drivers Manual

32XXX WinTV-PVR-250

30XXX WinTV-PVR-250

Hauppauge has a new SDK available for .NET applications. The SDK simplifies the development of TV applications in .NET. The SDK makes it easy for applications to perform functions like querying the available channels, start watching a channel in an application supplied window, pause/play, adjust volume, display OSD graphics, record live tv to a file, etc.

The SDK is provided under NDA and can be requested at support@hauppauge.com or sdk@hauppauge.co.uk


Windows 10 Anniversary Update requires special drivers to avoide errors during the Hauppauge product installation. Here are the updated drivers which can be used with the Windows 10 Anniversary Update

Note: these drivers are included in the

WinTV v8 installer, version 34245 or later

  • WinTV-dualHD and WinTV-soloHD
  • WinTV-HVR-955Q, WinTV-HVR-950Q, WinTV-HVR-955C
  • Xbox One TV tuner (ATSC)
  • WinTV-HVR-2255, WinTV-HVR-2215, WinTV-HVR-2205, WinTV-HVR-2200, WinTV-HVR-2250
  • WinTV-HVR-1975, WinTV-HVR-1955, WinTV-HVR-1950
  • WinTV-quadHD, WinTV-HVR-1265, WinTV-HVR-1250
  • HD PVR 2 (all models)
  • Colossus2
  • HD PVR 60
  • WinTV-NOVA-S-USB2, WinTV-NOVA-HD-USB2
  • WinTV-Nova-T stick, WinTV-Duet, WinTV-Nova-TD